If you want to move a BT socket you must purchase a special tool and this cost me £1.99. Didn't have that trouble moving a Chinese one!
Wiring the Sockets
Start at the last socket and finish at the Master Socket. For every cable at each socket, cut the sheath at the end of a cable about 13mm (1/2 in) with a pair of side cutters and expose the white nylon ripcord.
Grip the rip cord with a pair of long nosed pliers (curl the cord around the tips if it slips out) and pull firmly down, exposing the wires to about 50mm (2”).
Next cut away the unwanted sheath with the side cutters. Do not remove the PVC insulation from the wires themselves.
Fix the cable sheath(s) neatly to the cable mount on the faceplate of the socket using the nylon tie provided with the socket. Thread the tie through the slot/hole in the back of the faceplate. Put the cable in place and tighten the tie (see diagram below).
N.B. Cable securing methods may differ depending on the make of the socket.
Spread out the individual wires so that you can identify the colours. The first colour identified is the base colour of the plastic insulation, the second colour is printed over the first; for example, Green/White means green base, white overprint, White/Green means white base, green overprint.
In each socket the wiring HAS to be connected as follows:-
WARNING - make sure that you follow the colour coding correctly. Incorrect wiring may cause faulty operation or damage to the system.
Terminating the wires
No wire stripping or soldering is necessary to make a good termination.
The Krone tool (IDC - Insulation Displacement Connector) or cheap plastic wiring tool will be used to connect the wires to the socket.
IMPORTANT - do not attempt to insert the wires with anything other than the proper tools. Always wear eye shields when using IDC tools as the wire ends can fly off.
Support the socket faceplate firmly and hold the tool vertically making sure that the ‘blade’ of the tool is the correct way round. This is essential, as not only will the tool be damaged but also the wire will not be terminated properly if the tool is incorrectly used. It is recommended that you practice first by placing the IDC tool over a terminal, without a wire in place. In the correct position the tool will easily slide as far as the chamfer of the plastic insulator on the terminal.
Leaving a small amount of slack in the wire place the wire to be terminated in the appropriate slot of the terminal. Put the tool into position. A firm vertically applied pressure to the tool will force the wire into the connector fork and the connection is made. You will hear it go into place. Then remove any excess wire beyond the connector with the wire side cutters. The picture shows the cheap wiring tool, if the Krone version is used, then the scissors side locates in the recessed side (shown to the right in the picture). The Krone tool also automatically cuts off the spare wire.
If two cables are to be connected to the socket, a second wire will need to be inserted at the same terminal. Each wire must be inserted individually and not both at once. Ensure that wires are pushed into the connector fork fully, one on top of the other. The socket will only accommodate two cables maximum.
Where two wires are to be terminated at the same terminal, make sure that the colours of the wires from each cable match each other.
After you have made the three terminations on one side of the socket, e.g. 1,2,3 as shown above, turn the tool around to make the terminations for 4,5,6 so that the ‘blade’ of the tool (longer edge), is again facing towards the middle of the socket.
If you should make a mistake, a wire can be removed by pulling it upwards out of the connector fork. Do not attempt to reinsert the same part of the wire until the damaged portion has been cut off. Leave each terminated socket out of its box for the moment.
Lay the wires down onto the socket to make a neat job and then securely fix the socket to the back box.
Check for dial tone at each socket and then ask a friend to call you back. Whilst the line is ringing, plug a phone into each socket to ensure that it rings. If not check the termination on pin 3 of the socket.
How the UK Plug and Socket Telephone system works
What to do if you need to call your exchange supplier about a fault on your line